What项目号为R00114的山东晨鸣施胶辊,动平衡结束后,在包装时发

What
项目号为R00114的山东晨鸣施胶辊,动平衡结束后,在包装时发现在辊面传动侧位置表面有很多深色的突起的点,最长处距端面约500mm。

Where
老车间

When
2012年7月19日

Why
辊子在做动平衡时,操作人员把辊子端面的螺纹孔用243胶水拧上，由于涂上的胶水较多，在辊子旋转时胶水往四周甩出，并且由于在辊子传动侧位置放置有降温的电风扇，胶水落下时被电风扇吹向辊子中间部位，导致很多胶水水滴落在辊面，胶水和辊面起化学反应后，辊面起泡。

Corrective Actions
重新研磨辊面

Preventive Actions
辊子在做动平衡时，辊面必须包有缠绕膜，防止辊面有油污或其他不明液体滴在辊面上导致辊面出现缺陷.

Photos

ผลลัพธ์ (อังกฤษ) 1:

The What
Project No. R00114 Shandong Chenming the glue applying roller, dynamic balance after the end, found a lot of dark protuberances on the roller surface drive side position of surface points in the packaging, the strengths of about 500mm from the surface.

Where
old workshop

When
2012 July 19th

Why
roller in dynamic balance, the operator put the thread hole with 243 glue roller end surface of the screw, the coated with glue more, in the rotating roller glue to throw around, and due to the roller transmission side position with an electric fan cooling, glue down when the electric fan blowing to the roller intermediate parts, lead to a lot of glue water droplets on the roll surface,Glue and roll surface chemical reaction, the roller surface blistering.

Corrective Actions
re grinding roller surface

Preventive Actions
roller in dynamic balance, the roller surface must be covered with film, prevent the roller surface has oil or other unknown liquid drops in on the roller surface of roller surface defects in.

Photos

ผลลัพธ์ (อังกฤษ) 2:

What
item numbers R00114, Shandong chenming paper roll sizing, dynamic balance after the packaging found on the roller surface transmission points projecting surface has a lot of dark side, good point about 500mm from the end.

Where
old workshop

When
2012 years July 19

Why
roller in do moving balance Shi, operation personnel put roller end surface of thread hole with 243 glue twist Shang, due to coated Shang of glue more, in roller rotating Shi glue to around dumped out, and due to in roller drive side location placed has cooling of fan, glue falls Shi was fan blowing to roller middle parts, led to many glue water dripping in roller surface,After the glue roller surface reacts, roll surface froth.

Corrective Actions
re grinding roll surface

Preventive Actions
roller in dynamic balance, roll surface must be coated stretch film, preventing the roller surface of oil or other liquid droplets roller surface of unknown causes the roller surface defects on.

Photos

ผลลัพธ์ (อังกฤษ) 3:

What
item number to 00,114 R Shandong morning sounds glue roller, the balance after the packaging is found in the roller-drive side surface where there are many dark image of the point, the strengths to face about 500 mm.

Where
old shop

When
July 19, 2012

Why
roller in the balance, and the operator to roll the face of the threaded holes 243 in glue, and because the glue on more, the roller is rotating glue to 4 week thrown out, and as a result the roller drive side place a cooling fans of glue, when you drop the fans blow the roll center, resulting in many glue droplets from falling in the roller.Glue and roll-up after chemical reaction, roll the blisters.

Corrective Actions
re-grinding roller-

Preventive Actions
roller in the balance, roller-must have a winding film to prevent roll-oil or other unknown liquid in the roller-to-roller defect.
Photos